Intelligent It Solutions 's Sitemap

Products

Posts

During Nexus 7010 upgrade from 5.2.1 to 5.2.3 code, the X-bar module in slot 4 keeps powering off. The %MODULE-2-XBAR_DIAG_FAIL: Xbar 4 reported failure due to Module asic(s) reported sync loss (DevErr is LinkNum). Trying to Resync in device 88 (device error 0x0) error message is received.
Is there a best practice for port-channel load balancing between Nexus 1000V Series and Nexus 7000 Series Switches?
How do I implement VTP in a Nexus 7000 Series Switch where VLANs are manually configured?
How do I verify if XL mode is enabled on a Nexus 7000 device?
Can a Nexus 7000 be a DHCP server and can it relay DHCP requests to different DHCP servers per VLAN?
How do I capture the output of the show tech-support details?
How do I check the Network Time Protocol (NTP) status on a Nexus 7000 Series Switch?
On a Nexus 7000 running NX-OS 5.1(3), can the DecNet be bridged on a VLAN?
How do I enable/disable logging link status per port basis on a Nexus 7000 Series Switch?
When I issue the “show interface counters errors” command, I see that one of the interfaces is consistently posting errors. What are the FCS-Err and Rcv-Err in the output of the “show interface counters errors” command?
How can I avoid receiving the “Configuration does not match the port capability” error message when enabling “switchport mode fex-fabric”?
How do I avoid receiving the “Failed to process kickstart image. Pre-Upgrade check failed” error message when upgrading the image on a Nexus 7000 Series Switch?
When I issue the “show ip route bgp” command, I see my routes being learned via OSPF and BGP. How can I verify on the NX-OS which one will always be used and which one is a backup?
What is the equivalent NX-OS command for the “ip multicast-routing” IOS command, and does the Nexus 7000 support PIM-Sparse mode?
How do I redistribute connected routes into an OSPF instance on a Nexus 7010 with a defined metric?
On a Nexus, is the metric-type keyword not available in the “default-information originate” command?
What is the minimum NX-OS release required to support FCoE in the Nexus 7000 Series Switches?
Which Nexus 7000 modules support Fibre Channel over Ethernet (FCoE)?
How many OSPF processes can be run in a virtual device context (VDC)?
What are orphan ports?
Is Nexus 7010vPC feature (LACP enabled) compatible with the Cisco ASA etherchannel feature and with ACE 4710 etherchannel?
How many syslog servers can be added to a Nexus 7000 Series Switch?
Is there a tool available for configuration conversion on Cisco 6500 series to the Nexus platform?
How do I verify the features enabled on Nexus 7000 Series Switch with NX-OS 4.2?
What does the %EEM_ACTION-6-INFORM: Packets dropped due to IDS check length consistent on module message mean?
How do I create a peer link for VDC and a keepalive link for each VDC?
Why does vPC not block either of the vPC uplinks?
What is vPC and what are its benefits?
On a Nexus 7018, when trying to perform a ‘no shut’ on Ethernet 1/3, the ERROR: Ethernet1/3: Config not allowed
What is the command is used to verify the “HSRP Active State” on a Nexus 7000 Series Switch?
How do you configure and manage the Catalyst Micro Switches?
What is the Switch Database Management (SDM) template for the Catalyst Micro Switches?
How do you configure and manage the Catalyst Micro Switches?
What feature sets do the Catalyst Micro Switches support?
Do the Catalyst Micro Switches support the SD-Access architecture?
Do the Catalyst Micro Switches support Quality of Service (QoS)?
What are some of the key trustworthy technologies that the Catalyst Micro Switches support, and how do they protect the network?
Do the Catalyst Micro Switches support signed images?
What Cisco cyber threat defense security features do the Catalyst Micro Switches support?
How do the Catalyst Micro Switches help keep unauthorized users from accessing the network?

Go to full version: Intelligent It Solutions